Kit Steel Tanks

Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl

Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl
Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl
Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl
Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl
Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl
Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl

Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl

This SaniPLUS Upflush Kit Includes. The SaniPLUS macerating bathroom pump. White toilet bowl (size: standard).

Extension pipe (for behind the wall installation). UPC#s 002, 083, 005 and 030. The SaniPLUS is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniPLUS pump is designed to connect with. The SaniPLUS is simplicity itself to install; there are just four connections.

The macerating/pump is connected to the spigot of a horizontal outlet toilet. The toilet tank is connected to the water supply. The macerating/pump is connected to the small diameter discharge pipe work.

The macerating/pump is connected to the electrical supply. Then optionally connect the discharge pipes from the sink, shower and/or bath. The inside of the SaniPLUS comprises of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump. When the flush is activated, the water flowing into the SaniPLUS activates a microswitch in the pressure chamber, which in turn starts the motor.

The motor is sealed for life in oil filled enclosure. A common spindle drives the impeller and the macerator blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM. The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor. The pump operates at 10 PSI and pumps the effluent upward to 15 feet and/or 150 feet horizontally. Once the water is discharged and the water level in the container goes down, the microswitch deactivates the unit until the flush is activated again. A normal operating cycle for SaniPLUS takes about 15 - 18 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

In addition to the toilet waste, SaniPLUS will also discharge gray wastewater from a variety of other sanitary fixtures, such as: a hand basin, a bath, a bidet and a urinal. When adding a bathtub or shower, a base will have to be constructed, made out of 2" x 6" on edge, to allow for the installation of a P-trap and some gravity flow towards the pump unit. The wastewater from other sanitary fixtures is discharged into SaniPLUS via two 1 1/2-inch inlets, on either side of the housing. Either one or both inlets can be used as required. The discharge elbow on top of the Saniplus can be turned either to the left or to the right, depending on the discharge installation.

The SaniPLUS automatically adjust the input rate from other sanitary fixtures, always giving priority to the discharge water of the toilet. Inlet valves operated by a simple float mechanism achieve this. For example, if the bath is being emptied and the toilet is flushed simultaneously, the inrush of water from the toilet into the container slows down or stops the discharge from other fixtures for a few seconds, until the waste from the toilet has been dealt with. As the toilet water is discharged and the level in the container goes down the float valves open and the discharge from the other fixtures resumes. The SaniPLUS is designed to provide vertical pumping up to 15 feet as well as a horizontal discharge, therefore a simple ball non-return valve is incorporated. It has now become possible to install a complete bathroom where previously this would have been impossible or where considerable capital equipment and structural work would have been necessary. The water closet the SaniPLUS is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush.

UPC#s 002, 003 and 005. H12" x W21" x D9. H30cm x W53cm x D23cm.

No carbon brushes or gears. Tested over 30,000 cycles. Horizontally to 150 ft (50m). Gravity Fall on Horizontal installations: 1/4 per ft. Pumps vertically to 15 ft (4m).

Subject to installation pipe run. Top rated, authorized SaniFlo dealer.

Veteran in online sales and fulfilment. In our offices here, and it gets used ALL THE TIME from everyone drinking too much coffee lol. But it works great, no issues, would definitely put another one in. We have had major clogging issues with our other toilets, but this one works great. I've never had a problem with it.

Got to my house in 3 days. Just top-notch ecommerce site all round. White toilet bowl (size: Elongated). SaniPlus Standard Bowl + Extension. SaniPlus Elongated Bowl + Extension. SaniPlus Standard Bowl + SaniAlarm.

SaniPlus Elongated Bowl + SaniAlarm. SaniPlus Standard Bowl + Extension + SaniAlarm. SaniPlus Elongated Bowl + Extension + SaniAlarm. A normal operating cycle for SaniPLUS takes about 15-18 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.


Saniflo SaniPLUS Upflush Macerating Toilet Kit Pump + Elongated Bowl